Part : AB68-00504D(00)Printed in ChinaSCC-C6405(P)ERUSmartDome CameraOwner’s InstructionsêÛÍÓ‚Ó‰ÒÚ‚ÓÔÓθÁÓ‚‡ÚÂÎfl
To install and use the SCC-C6405(P), the following cables should beprepared.Power Adapter CableThe cable that plugs into the SCC-C6405(P) power input
Installing SCC-C6405(P)Installation Precautions1) Make sure that the installation site can sufficiently support a minimum offour times the net weight
5) CEILING MOUNT ADAPTOR (SADT-100CM)This adaptor is used for installing the indoor housing or the outdoorhousing for the SmartDome Camera to a concre
2-9E2-87. [Figure 7] Match the 3 holes on theback of the CAMERA and theCONNECTOR and turn it left about15 degrees.(Check the sound of LOCKING and that
3-2E3-1Structure of the Setup MenuIn this chapter, we will look over the Setup Menu of the SCC-C6405(P), First we'll look over the overall struct
3-3 3-4E1. CAMERA SET MENUCAMERA IDThe CAMERA ID menu assigns an ID to the SCC-C6405(P) to be displayedon the connected monitor.On the CAMERA SET menu
3-5 3-6ECOLOR/BWIn the COLOR/BW menu, you can switch ON or OFF the IR (infrared) Filter.In a poor illumination environment, the IR filter is turned of
3-8EEXITThe EXIT menu is used to quit the CAMERA SET menu of the SCC-C6405(P) and return to the MAIN MENU.- QUIT : Ignores the changed information and
3-10E- LEVEL 1 : Controls the shutter speed while WDR operates.- LEVEL 2 : Controls the whole brightness while WDR operates.- FLIKERLESS : This is
3-12EWHITE BAL Lights are generally denoted as color temperatures and expressed inKelvin (K) units. The general light color temperatures are shown b
EImportant Safety InstructionsSafety PrecautionsThe purpose of this information is to ensure proper use of this product toprevent danger or damage to
3-14EFOCUS MODEIn the FOCUS MODE MENU, the Focus method can be set to AF, MF, or ONEAF.- AF : With AUTO FOCUS MODE, you can monitor the screen continu
3-16EPOSITION SETFrom "POSITION SET..." press [ENTER] to get into the PAN/TILT,FOCUS/ZOOM SET screen to set the PAN/TILT location and FOCUS/
3-18EBLANK ALL BELOWThe available angle for setup ranges from OFF/0/-10 to -90 and the areabelow a set angle will be regarded as the ZONE area.PRYVACY
3-20EREVERSEThe REVERSE function applies PRIVACY MASK to the other area thanset as a privacy zone. ON/OFF is available.ZONE DIR SET/ZONE AREA SETThis
3-22ELOCATIONThe “LOCATION...” menu designates the left/right LIMIT positions ofZONE AREA. Enter the setup screen to move PAN, then select a startposi
3-24EDIRECTIONThis sets up the movement direction of the START to END location (PAN location standard)"RIGHT " :
3-26EAUTO PLAYAUTO PLAY executes SCAN, AUTO PAN, PATTERN, and PRESET when thereis no camera action after AUTO RETURN finishes.AUTO RETURNThis menu set
3-28E7. OTHER SET PROPORTIONAL P/TThis function controls the PAN/TILT speed to the ZOOM magnificationratio during the manual operation of PAN/TILT. If
3-30E3-29TURBO P/TThis function doubles up the speed of PAN/TILT movement by manualoperation of PAN/TILT. The speed may go up to 180°/sec(PAN).AUTO CA
3-32E3-319. SHORT KEYSSSC-1000 or SSC-2000 Controller supports the following short keys.Other keys than AUTO CAL. and AUTO RETURN, upon execution, sha
6. Do not place conductive objects (e.g., screwdrivers, coins, and metal things) or containers filled with water on top of the camera. (Doing so mayca
3-34EProduct specificationsSCC-C6405Contents- Zoom lens single body WDR SmartDome CAMERA- AC 24 ± 10% (60Hz ± 0.3Hz)- 18W- NTSC STANDARD COLOR SYSTEM
ECautions• The copyright of the manual belongs to Samsung Electronics Co., Ltd.•Without the permission of Samsung Electronics it cannot be reproducede
1-2E1-1Before UsageThis is a basic instruction manual for the SCC-C6405(P) user. It contains all the instructions needed to use the SCC-C6405(P)from
1-4E1-34. ZONE SET ...3-17- PRIVACY ZONE ...
1-6E1-5SCC-C6405(P) IntroductionSCC-C6405(P) is a zoom lens built in smart dome camera whichprovides you with the best monitoring function in connecti
1-8E1-7AC 24V OUTPOWERAC 24V OUTPOWERBACKLocations of ControlFRONT
1-10E1-9INITIAL SETTINGCAMERA ADDRESS SETUPUse SW701, SW702, or 703 for Camera Address setup. You may allocateup to 255 addresses by using SW701 to se
2-1E1-11Setting RS-422A/RS-485 termination12As it is shown in the structure map, when Controller and RS-422A/RS-485 is connected it should be terminat
Kommentare zu diesen Handbüchern