Samsung WF231 Series Bedienungsanleitung PDF herunterladen

Fast Track Troubleshooting

Model:

WF231ANW

Publication # rsWF231 Revision Date 12/20/2011

Quick Test Mode

Note: This test erases all faults and memory:

To enter press Soil, Spin, & Power simultaneously

with the power off.

1. All LED’s light up and the washer beeps as it

enters the Quick Test Mode.

2. The unit displays the software version for a

second then clears the EEprom. If EEEE is dis-

played the PCB ass’y is defective.

3. When the version is displayed, turn the Jog-Dial

so that the version disappears. Each step of the

Jog-Dial displays the following; cycle count, water

level frequency, water temperature, EP condition,

test, spin, version.

Press the following keys to test the various compo-

nents.

Water valves: (lock the door first) Press Temp Key to

cycle in this order: Bleach, Cold Main, Hot & then off.

Door Lock/Unlock: Press Spin Key.

Drain Pump: Press Signal Key.

Water heater: Press Soil Level Key.

Motor test: When either Test or Spin is displayed on

the LCD, press Start/Pause key.

Test mode: You can test the clockwise and counter-

clockwise movement of the motor. However, the water

level must satisfy the heater water level (24300) to en-

ter Test mode.

Spin mode: You can test the motor at a high rpm.

Service Mode:

This mode allows more detailed operation tests and trouble-

shooting, to enter press Delay Start & Spin simultaneously

with the power on.

While in Service Mode the following tests can be performed:

Quick Spin Test = Delay Start & Temp : This accelerates

the drum motor from 0 to maximum RPM over a few min-

utes. Note: Stay with the washer during this test, out of bal-

ance detection is bypassed and the door may not lock.

Press the Start/Pause button during the test to hold its spinning

speed for 10 minutes before going back to Quick Spin Test

Mode.

Cycle Count = Press the Signal button to see how many times

the unit was used

Soft Ware # = Press the Soil button to see the software version

information

Fast Time Down = Start Cycle, then Service mode. Press the

Temp button to advance to the next cycle

Fault Code Test = Press the Spin button to view the stored fault

codes – then turn Jog Dial to view error codes (Push Start/

Pause while the code is displayed to view the cycle # that the

error occurred)

Peripheral (Main PCB) input Tests; Select Extra Rinse

(display shows ln)

1. Water Temperature; Turn the Jog-Dial so that the Heavy

Duty LED is turned on. The Water Temperature will be dis-

played in Fahrenheit.

2. Door status; Turn the Jog-Dial so that the Permanent Press

LED is turned on. The door status will be displayed (OP if open,

CL if closed).

3. Door lock; Turn the Jog-Dial so that the Sanitize LED is

turned on. The door lock Switch status will be displayed (UL if

unlocked, Lo if locked).

4. Water Frequency; Turn the Jog-Dial so that the Pure Cycle

LED is turned on. The Water Frequency will be displayed.

IMPORTANT SAFETY NOTICE – “For Technicians Only” This service data sheet is intended for

use by persons having electrical, electronic, and mechanical experience and knowledge at a level

generally considered acceptable in the appliance repair trade. Any attempt to repair a major appliance

may result in personal injury and property damage. The manufacturer or seller cannot be responsible,

nor assume any liability for injury or damage of any kind arising from the use of this data sheet.

Demo mode: With power on press Pure cycle and

Extra rinse. ‘----‘ is displayed.

Wash; press Temp. UASH is displayed. Press Start

and agitator operates for 5 minutes without water.

Spin; press Spin. SPin is displayed. Press Start and

unit spins to 1030 RPM for 4 minutes without water.

LED; press Soil. LEd is displayed. Press Start and all

lLEDs are lit for 30 seconds.

1 2 3 4 5 6 7

Inhaltsverzeichnis

Seite 1 - Fast Track Troubleshooting

Fast Track Troubleshooting Model: WF231ANW Publication # rsWF231 Revision Date 12/20/2011 Quick Test Mode Note: This test erases all

Seite 2

Seite 3 - Washer Connector Checks

Washer Connector Checks CN2 1 AC Pwr (L) (Blu) 3 Valves (N), Lock Sw (Blk) (N) w/ door locked RY1 Power Relay 1 (Wht) (N) 2 (Blu) CN8 (Display Conn

Seite 4 - -The unit needs to be on

Door Lock Check Test 1 Test 2 Connector CN2, pin 1 (BLUE) and CN2 Pin 3 (BLACK) When Door is Locked 120VAC Unlocked 0VAC With Power Off, the resista

Seite 5

Error Type Error Mode Details LED LCD Drain Error nD 1 Che

Seite 6

When installing a washer and dryer on the first, or second floor, do not exceed this leg adjustment height for stability. Foot Pad for Walking Washer,

Seite 7 - MANUAL-BOOK DC68-02535A

Water valve connections for the Detergent Drawer Laundry Touch Up Paints TOUCH UP PAINT, BLUE ONYX DH81-11980ATOUCH UP PAINT, IMPERIAL SILVER DH81-119