Samsung WF330ANW/XAA Bedienungsanleitung PDF herunterladen

Fast Track Troubleshooting

Model: WF330ANW/XAA

Publication # tsWF330 Revision Date 08/12/2010

Quick Test Mode:

Note: This test erases all faults and memory

To enter press Soil, Signal, & Power

simultaneously with the power off.

1. All LED’s light up and the washer beeps as it

enters the Quick Test Mode.

2. The unit displays the software version.

3. After the displaying the software version, turn

Jog dial CCW until version disappears.

Press Spin to test Door Lock/Unlock circuit.

Press Temp Key (with door locked) to cycle through

the Water Valves circuit test in this order: Pre, Bleach,

Cold Main, Hot, Boot valve, then off.

Press Soil Key to test the Heater

Press Signal Key to test the Pump

Service Mode:

This mode allows more detailed operation tests and

troubleshooting, to enter press Signal & Delay Start

simultaneously with the power on.

While in Service Mode (the Service Mode can be entered

while the unit is in a wash cycle) the following tests can

be performed:

Quick Spin Test = Delay Start & Pre Wash: This acceler-

ates the drum motor from 0 to maximum RPM over a few

minutes. Press the Start/Pause button during the test to hold

its spinning speed up to 10 min. before going back to Quick

Spin Test Mode, return to spin with Delay Start & Pre Wash.

Cycle Count = Press the Signal button to see how many

times the unit was used.

Soft Ware # = Press the Soil Level button to see the software

version information

Fault Code Test = Press the Pure Cycle button to view the

stored fault codes – then turn Dial to view error codes (Push

Start/Pause while the code is displayed to view the number of

cycles since the error occurred, push Start/Pause again to get

back to faults)

Peripheral (Main PCB) input Tests, enter Service Mode &

press Spin key.

1. Turn the Dial so that the Extra Rinse LED is turned on.

Next, press the Start/Pause Key. Temperature will be dis-

played in Fahrenheit.

2. Turn the Dial so that the Cold/Cold LED is turned on. Next,

press the Start/Pause Key. The door switch status will be dis-

played (CL if Closed, OP if Open).

3. Turn the Dial so that the No Spin LED is turned on. Next,

press the Start/Pause Key. The door lock Switch status will be

displayed (UL if unlocked, LO if locked).

4. Turn the Dial so that the Light LED is turned on. Next,

press the Start/Pause Key. The Water Frequency will be dis-

IMPORTANT SAFETY NOTICE – “For Technicians Only” This service data sheet is

intended for use by persons having electrical, electronic, and mechanical experience

and knowledge at a level generally considered acceptable in the appliance repair trade.

Any attempt to repair a major appliance may result in personal injury and property

damage. The manufacturer or seller cannot be responsible, nor assume any liability for

injury or damage of any kind arising from the use of this data sheet.

Spin Only option:

Power on, Press and hold Spin until display changes.

Press Spin to select spin time.

Press Start/Pause to start cycle, Normal Cycle 10/12

minutes, Heavy Duty Cycle 11/13 minutes, Delicate

Cycle 8 minute. Spin speed varies with cycle.

EEPROM Clear Check

Power off, Press Delay Start, Signal and Power Key at

the same time. Good = Good Fail = FAiL

All memory will be cleared, including Fault Codes

This should be done when a new Main PCB is installed

Fabric Softener Dispenser Test:

Start Rinse and Spin Cycle. After fill is completed

remove detergent drawer, place towel below opening

and within 3 minutes the dispenser will activate

Please Note:

There are two Versions of

this model, when ordering

parts please verify the

version you are servicing.

1 2 3 4 5 6 7

Fast Track Troubleshooting 1

Inhaltsverzeichnis

Seite 1 - Fast Track Troubleshooting

Fast Track Troubleshooting Model: WF330ANW/XAA Publication # tsWF330 Revision Date 08/12/2010 Quick Test Mode:

Seite 2

Seite 3

Washer Connector Checks WF330 CN2 1 AC Pwr (Blk) 2 Power off Detection (Yel) 3 Doo

Seite 4

Error Type Error Mode Details LED LCD Water Level Sensor LE 8 Che

Seite 5

Error Type Error Mode Details LED LCD Drain Error nD 1 Chec

Seite 6

When installing a washer and dryer on the first, or second floor, do not exceed this leg adjustment height for stability. Error Type Error Mode De

Seite 7

Water valve connections for the Detergent Drawer Items Packed With Washer BOLT-SPANER (10-13mm Wrench) DC60-40146A ASSY HOSE WATER Cold DC97-15648A

Kommentare zu diesen Handbüchern

Keine Kommentare

Samsung WF330ANW/XAA Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Waschmaschinen Samsung WF330ANW/XAA herunter. Fast Track Troubleshooting Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Waschmaschinen Samsung WF330ANW/XAA