Samsung WF338AAB Bedienungsanleitung PDF herunterladen

Fast Track Troubleshooting

Publication # tsWF338 Revision Date 8/10/2010

Quick Test Mode

Note: This test erases all faults and memory:

To enter press Soil, Signal, & Power

simultaneously with the power off.

NOTE On early production: To enter press Soil,

Steam, & Power simultaneously with the power off.

1. All LED’s light up and the washer beeps as it

enters the Quick Test Mode.

2. The unit displays the software version for a

second then clears the EEprom.

3. After the displaying the software version, LCD

will display Model information. If EEEE is displayed

the PCB ass’y is defective.

4. When the version is displayed, turn the Jog-Dial

so that the version disappears. Press the following

keys to test the various components

Press Temp Key to cycle through the Water Valves

circuit test (lock the door first) in this order: Pre-Wash,

Bleach, Cold Main, Hot, & Steam, then off.

Press Spin Key to test Door Lock/Unlock circuit

Press Soil Level Key to test Circulation/Drain Pump.

Press Signal Key to test the Water/Steam Heater.

When either Test or Spin is displayed on the LCD,

press Start/Pause key to conduct the motor test.

In Test mode, you can test the clockwise and counter-

clockwise movement of the motor. However, the water

level must satisfy the heater water level (24300) to en-

ter Test mode.

In Spin mode, you can test the motor at a high rpm.

Service Mode:

This mode allows more detailed operation tests and trouble-

shooting, to enter press Signal & Extra Rinse

simultaneously with the power on.

While in Service Mode the following tests can be performed:

Quick Spin Test = Delay Start & Silver Care: This acceler-

ates the drum motor from 0 to maximum RPM over a few

minutes. Note: Stay with the washer during this test, out of

balance detection is bypassed and the door may not lock.

Press the Start/Pause button during the test to hold its spinning

speed for 10 minutes before going back to Quick Spin Test

Mode.

Cycle Count = Press the Signal button to see how many times

the unit was used

Soft Ware # = Press the Soil button to see the software version

information

Fast Time Down = Press the Temp button to advance to the

next cycle

Fault Code Test = Press the Silver Care button to view the

stored fault codes – then turn Jog Dial to view error codes

(Push Start/Pause while the code is displayed to view the num-

ber of cycles since the error occurred)

Peripheral (Main PCB) input Tests

1. Select Extra Wash

. Then turn the Jog-Dial so that the Extra

Rinse LED is turned on. Next, press the Start/Pause Key. The

Water Temperature will be displayed in Fahrenheit.

2. Select Extra Wash

. Then turn the Jog-Dial so that the Extra

Spin LED is turned on. Next, press the Start/Pause Key. The

door status will be displayed (OP if open, CL if closed).

3. Select Extra Wash

. Then turn the Jog-Dial so that the Delay

Start LED is turned on. Next, press the Start/Pause Key. The

door lock Switch status will be displayed (UL if unlocked, Lo if

locked).

4. Select Extra Wash

. Then turn the Jog-Dial so that the Pre

Wash LED is turned on. Next, press the Start/Pause Key. The

Water Frequency will be displayed.

5. Select Extra Wash

. Then turn the Jog-Dial so that My Cycle

LED is turned on. Next, press the Start/Pause Key. The AG Kit

status will be displayed after 3 seconds. (“ㅂE” if the AG kit is

abnormal. “—” if the AG Kit is working properly)

IMPORTANT SAFETY NOTICE – “For Technicians Only” This service data sheet is

intended for use by persons having electrical, electronic, and mechanical experience

and knowledge at a level generally considered acceptable in the appliance repair trade.

Any attempt to repair a major appliance may result in personal injury and property

damage. The manufacturer or seller cannot be responsible, nor assume any liability for

injury or damage of any kind arising from the use of this data sheet.

Model: WF338***/XAA

BOM Models

WF338AAW/XAA

WF338AAR/XAA

WF338AAG/XAA

WF338AAB/XAA

EEPROM Clear Check

Power off, Press Delay Start, Signal and Power Key at

the same time. Good = Good Fail = FAiL

All memory will be cleared, including Fault Codes

This should be done when a new Main PCB is

installed

1 2 3 4 5 6 7

Inhaltsverzeichnis

Seite 1 - Fast Track Troubleshooting

Fast Track Troubleshooting Publication # tsWF338 Revision Date 8/10/2010 Quick Test Mode Note: This test erases all faults and memory: To enter p

Seite 2 - WF338AA*

WF338AA* Gray Gray CN1 2

Seite 3

Washer Connector Checks WF448 CN3 1 Door Lock Close (Blk) 2 Door Lock Open (Wht) 3 Drain Pump (Vio) 4 Steam Valve (Red) 5 Bleach Valve (Pnk) 7 Pre Va

Seite 4

Door Lock Check Test 1 Test 2 Connector CN2 Pin 3 (Brown) and CN3 Pin 1 (Black) When Door is Locked or Unlocked there is a pulse of 120VAC for a few

Seite 5

Error Type Error Mode Details LED LCD Drain Error nD 1 Chec

Seite 6

When installing a washer and dryer on the first, or second floor, do not exceed this leg adjustment height for stability. Foot Pad for Walking Washer,

Seite 7 - Softener

Pre WashMai n WashSoftenerBleachPath #2Path #1Path #3Path #4Path #5V#1 V#2 V#3 V#4 V#5MAIN(H) PRE WASH BLEACH MAIN(C) STEAMWater valve connections for